One-pot foam-gelcasting/nitridation synthesis of high porosity nano-whiskers based 3D Si3N4 porous ceramics

Nano-whiskers based 3D Si₃N₄ porous ceramics (3D-NWSNPC) with high-porosity (about 91–93 %), low density (0.17–0.25 g/cm³), low thermal conductivity, and a certain degree of recoverability under cyclic compressive loading and reasonably strengths were prepared at 1423–1523 K via a one-pot foam-gelcasting/nitridation route using inexpensive commercial Si powders as starting materials and hexadecyl trimethyl ammonium bromide as foaming agent. After nitridation at 1523 K, the sample with an original solid loading of 12.5 wt% exhibited the highest compressive strength of 1.9 MPa, even though its density was lowered to 0.25 g/cm³. The sample nitrided at 1473 K had a relative density of 7.3 %. Its compressive and specific strength were respectively 1.1 MPa and 5.5 MPa·cm³ g^?1, and its thermal conductivity was as low as 0.074 W/(m K) (measured at 323 K). These outstanding properties would make the as-prepared 3D-NWSNPC a promising candidate for applications in catalysis, filtration, thermal insulation and many other important areas.     

Defect Engineering in Ambipolar Layered Materials for Mode-Regulable Nociceptor

Defect engineering represents a significant approach for atomically thick 2D semiconductor material development to explore the unique material properties and functions. Doping-induced conversion of conductive polarity is particularly beneficial for optimizing the integration of layered electronics. Here, controllable doping behavior in palladium diselenide (PdSe₂) transistor is demonstrated by manipulating its adatom-vacancy groups. The underlying mechanisms, which originate from reversible adsorption/desorption of oxygen clusters near selenide vacancy defects, are investigated systematically via their dynamic charge transfer characteristics and scanning tunneling microscope analysis. The modulated doping effect allows the PdSe₂ transistor to emulate the essential characteristics of photo nociceptor on a device level, including firing signal threshold and sensitization. Interestingly, electrostatic gating, acting as a neuromodulator, can regulate the adaptive modes in nociceptor to improve its adaptability and perceptibility to handle different danger levels. An integrated artificial nociceptor array is also designed to execute unique image processing functions, which suggests a new perspective for extension of the promise of defect engineered 2D electronics in simplified sensory systems toward use in advanced humanoid robots and artificial visual sensors.     

东北地区传统发酵食品中两株植物乳杆菌的安全性评价

针对已分离的植物乳杆菌L12和L20通过体外和体内两种方法进行安全性评价。通过体外实验测定乳酸水解活性抗生素敏感性，胆盐水解酶活性，D-乳酸含量，γ溶血等指标；体内实验是对小鼠进行短期口服毒性的研究，口服0.2 mL（109 CFU/mL）的实验性细菌溶液30 d。结果表明，体外实验中，两株菌株均具有良好的抗氧化活性，对抗生素敏感性高，胆盐水解酶活性高，D-乳酸含量低，γ溶血；体内实验中灌胃给药对治疗小鼠的生长、行为、摄食量、器官重量或组织病理学分析均无不良影响。与对照组相比，益生菌组小鼠血清MDA浓度和肝脏GSH含量差异有统计学意义(P<0.05)。这些结果表明，菌株L12和L20是非致病性的，人直接食用是安全的。     

Position-varying surface roughness prediction method considering compensated acceleration in milling of thin-walled workpiece

Machined surface roughness will affect parts’ service performance. Thus, predicting it in the machining is important to avoid rejects. Surface roughness will be affected by system position dependent vibration even under constant parameter with certain toolpath processing in the finishing. Aiming at surface roughness prediction in the machining process, this paper proposes a position-varying surface roughness prediction method based on compensated acceleration by using regression analysis. To reduce the stochastic error of measuring the machined surface profile height, the surface area is repeatedly measured three times, and Pauta criterion is adopted to eliminate abnormal points. The actual vibration state at any processing position is obtained through the single-point monitoring acceleration compensation model. Seven acceleration features are extracted, and valley, which has the highest R-square proving the effectiveness of the filtering features, is selected as the input of the prediction model by mutual information coefficients. Finally, by comparing the measured and predicted surface roughness curves, they have the same trends, with the average error of 16.28% and the minimum error of 0.16%. Moreover, the prediction curve matches and agrees well with the actual surface state, which verifies the accuracy and reliability of the model.     

湿法炼锌赤铁矿法沉铁行为

湿法炼锌工艺过程中赤铁矿法沉铁技术是一种沉淀渣量小、分离效率高的锌、铁分离方法。针对湿法炼锌工艺过程中赤铁矿法沉铁技术开展了硫酸亚铁的氧化水解沉淀行为的研究，考察了时间、酸度、温度、硫酸盐浓度、晶种返回量等主要因素对赤铁矿法沉铁效果的影响、沉淀产物的析出特性和物相表征。     

Effect of processing method on vitamin profile,antioxidant properties and total phenolic content of coconut (Cocos nucifera L.) sugar syrup

Coconut (Cocos nucifera L.) sugar is a more nutritious alternative sugar source as compared to sugar palm (Borassus flabellifer) and sugarcane (Saccharum officinarum L.). This work was aimed to investigate the browning index (BI), vitamin profile and antioxidant properties of coconut sap sugar syrups, which were produced by different processing methods: rotary evaporation (RE), microwave evaporation (ME) and open-heat evaporation (OHE). The results obtained showed that coconut sugar syrup produced by RE-60 contained high antioxidant activities [DPPH (36.71%) and ABTS (34.84%), TPC (299.87 mg per 100 g sample) and FRAP (3.74 mm )]. These values were slightly lower than those of ME and OHE. Coconut sugar syrup (RE-60) also contained higher amounts of vitamin C (1587.27 mg L⁻¹), vitamin B1 (97.44 mg L⁻¹) and vitamin B3 (19.84 mg L⁻¹) compared with those of ME and OHE coconut sugar syrups. RE-60 was the best method to produce coconut sugar syrup in a shorter time with lower browning index and higher vitamin contents.     

Fabrication and Thermal Dissipation Properties of Carbon Nanofibers Derived from Electrospun Poly(Amic Acid) Carboxylate Salt Nanofibers

Polyimides (PIs) possess excellent mechanical properties, thermal stability, and chemical resistance and can be converted to carbon materials by thermal carbonization. The preparation of carbon nanomaterials by carbonizing PI‐based nanomaterials, however, has been less studied. In this work, the fabrication of PI nanofibers is investigated using electrospinning and their transformation to carbon nanofibers. Poly(amic acid) carboxylate salts (PAASs) solutions are first electrospun to form PAAS nanofibers. After the imidization and carbonization processes, PI and carbon nanofibers can then be obtained, respectively. The Raman spectra reveal that the carbon nanofibers are partially graphitized by the carbonization process. The diameters of the PI nanofibers are observed to be smaller than those of the PAAS nanofibers because of the formation of the more densely packed structures after the imidization processes; the diameters of the carbon nanofibers remain similar to those of the PI nanofibers after the carbonization process. The thermal dissipation behaviors of the PI and carbon nanofibers are also examined. The infrared images indicate that the transfer rates of thermal energy for the carbon nanofibers are higher than those for the PI nanofibers, due to the better thermal conductivity of carbon caused by the covalent sp² bonding between carbon atoms.     

Comparison of the Crystallization Behavior of Silica Between Mg- and Al-Phosphate Used in Tension Coatings of Grain-Oriented Electrical Steel

Metals and Materials International - The effect of the phosphate component on the thermal stability of tension coatings was investigated with a focus on the crystallization behavior of amorphous...